Common Failures of Hydraulic Gear Pumps


Release time:

2023-08-31

If you find that the gear pump does not come to oil in the host commissioning, first check whether the rotation direction of the gear pump is correct. Gear pumps have left, right rotation points, if the direction of rotation is not correct, its internal gear meshing volume difference formed by the pressure oil will make the oil seal is broken and oil leakage. Secondly,

1. Pump does not come out of the oil
If you find that the gear pump does not come to oil in the host commissioning, first check whether the rotation direction of the gear pump is correct. Gear pumps have left, right rotation points, if the direction of rotation is not correct, its internal gear meshing volume difference formed by the pressure oil will make the oil seal is broken and oil leakage. Secondly, check whether the oil filter at the inlet end of the gear pump is clogged, which will cause difficulty in sucking oil or sucking oil, and produce the phenomenon that the suction hose is sucked flat.
2. Oil seal washed out
(1) The gear pump is not rotated correctly. When the rotation of the pump is incorrect, high-pressure oil will be directly to the oil seal, because the general low-pressure skeleton oil seal can only withstand the pressure of 0.5MPa, so the oil seal will be washed out.
(2) Gear pump bearing to the axial force. Generate axial force is often associated with the gear pump shaft extension end with the shaft sleeve is too tight, that is, the installation of the pump with a hammer or through the installation of screws to pull the pump shaft by a backward axial force, when the pump shaft rotation, the backward axial force will force the pump to intensify the wear and tear. As the internal gear pump is relying on the gear end face and sleeve end face fit sealing, when its axial sealing end face wear is serious, the pump internal axial sealing will produce a certain gap, which leads to the high and low pressure oil cavity communication and make the oil seal flushed out. This situation occurs more in the dump truck industry, mainly due to irregularities in the size of the coupling sleeve on the host.
(3) The gear pump is subjected to excessive radial force. If the coaxiality of the gear pump installation is not good, it will make the pump subjected to radial force beyond the capacity of the oil seal, which will cause the oil seal leakage. At the same time, it will also cause the pump internal floating bearing damage.
(4) Gear pumps for a long time suction or semi-vacuum, so that the pump gear end face and sleeve wear increased, because the gear pump is relying on the internal gear end face and sleeve end face sealing, when the axial sealing end face wear is serious, the pump internal axial sealing will produce a certain gap, which leads to the communication between the high and low pressure oil cavities and make the oil seal flushed out.
3. Establishment of pressure or pressure is not enough
Most of this phenomenon is related to the cleanliness of the hydraulic fluid, such as fluid selection is not correct or the use of the cleanliness of the fluid does not meet the standard requirements, will accelerate the internal wear of the pump, resulting in that leakage. Therefore, should be used with additives containing mineral hydraulic oil, which can prevent the oil oxidation and bubbles. The viscosity of the oil standard (16 ~ 80) × 10-6m2 / s filtration accuracy: input oil less than 60цm. By observing the failure of the gear pump bushings and side panels found that if all the oil cleanliness will lead to friction on the surface of the surface of the obvious grooves, and normal wear of the sealing surface of the gear pump will only produce a uniform surface marks.
4. Flow rate is not up to standard
(1) The oil filter element is too dirty, insufficient oil suction.
(2) The installation height of the pump is higher than the self-priming height of the pump.
(3) The suction pipe of the gear pump is too thin, resulting in high suction resistance. The general suction flow rate is 0.5-1.5m/s.
(4) suction port connector air leakage caused by the pump suction oil is insufficient. By observing whether there are air bubbles in the oil tank, you can determine whether the system is leaking.
5. Gear pump cracking
Aluminum alloy material gear pump pressure resistance of 38 ~ 45MPa, in its absence of manufacturing defects in the premise, the gear pump cracked certainly by the instant high pressure.
(1) The oil outlet pipe is blocked with foreign matter, causing the pressure to rise indefinitely.
(2) The safety valve pressure adjustment is too high, or the opening and closing characteristics of the safety valve is poor, lagging response, so that the gear pump is not protected.
(3) System such as the use of multi-way reversing valve control direction, some multi-way valve may be negative opening, which will encounter due to the dead point of the pressure rise and suffocate the gear pump.
6. Heat
(1) System overload, mainly in the pressure or speed is too high.
(2) poor oil cleanliness, internal wear and tear increases, so that the volumetric efficiency decreases, oil leakage from the internal gap throttling and heat.
(3) The oil outlet pipe is too thin, the oil flow rate is too high, the general oil outlet flow rate is 3 to 8m/s.

Key words: