Duplex Gear Pumps in Coal Mining Machine Elevation Systems


Release time:

2020-01-05

Coal mining machine heightening system is generally hydraulic heightening, hydraulic system has a single pump and duplex gear pumps, the oil system can be simplified for the main oil, control oil, brake oil, a total of the main oil to control the two hydraulic cylinders to lift the rocker arm, the required flow rate is larger, the required oil pressure is slightly less than the high-pressure relief valve oil pressure. Control oil circuit only control the action of the hand-hydraulic reversing network, the required flow is less, brake oil circuit with oil compression brake pads to achieve braking efficiency, the same required flow is small, the oil circuit required oil pressure of about 2MPa. This paper compares the hydraulic system.

Coal mining machine heightening system is generally hydraulic heightening, hydraulic system has a single pump and duplex gear pumps, the oil system can be simplified for the main oil, control oil, brake oil, a total of the main oil to control the two hydraulic cylinders to lift the rocker arm, the required flow rate is larger, the required oil pressure is slightly less than the high-pressure relief valve oil pressure. Control oil circuit only control the action of the hand-hydraulic reversing network, the required flow is less, brake oil circuit with oil compression brake pads to achieve braking efficiency, the same required flow is small, the oil circuit required oil pressure of about 2MPa. This paper compares the hydraulic system.

1, the oil tank heat dissipation:

When the hydraulic oil through the mesh block, due to the existence of elbows, joints, mesh mouths and sudden changes in the cross-section, etc., due to the circulation or flow direction of the speed change in the local area of the flow resistance caused by pressure loss, resulting in an increase in oil temperature.

And duplex gear pump system principle in the main oil circuit because there is no pressure drop, power waste is mainly in the control oil circuit. From the calculation results, to achieve the oil tank cooling requirements, single pump configuration tank than the duplex pump tank is larger than the requirement of short body of the coal mining machine design is not favorable.

2, control valve life:

In the single-pump hydraulic system, the main oil circuit of the oil as a whole into the control oil circuit, the flow rate is larger, in the control of the thicker hydraulic pipe shall be used. At the same time, in the control, the oil through more small holes, the pressure loss is more serious. Large flow also means that there are more impurities may enter the control oil circuit with the flow of liquid, which can easily cause electromagnetic commutation network or pipeline blockage, resulting in downtime maintenance accidents. Duplex pump system, because the control oil circuit for a relatively separate circuit, the small pump through the main return pipe oil suction, into the pump body, through the fine filter, to protect the quality of the fluid, a greater reduction in the occurrence of hydraulic system failures.

3, power loss:

Oil through the pump first through the left and right rocker hydraulic cylinder net group in the middle (H) into the control oil circuit, when not in operation, not through the electromagnetic commutation net, through a low-pressure overflow net (2MPa) back to the tank. There is a high pressure overflow net (20MPa) at the outlet of the oil pump. When cranking up the oil first into the cylinder and then into the control oil circuit, when the pump is working at full load (i.e., the export oil pressure of 20MPa), the hydraulic pump supply hydraulic cylinder oil pressure of 18MPa, visible 10% power waste.

In the duplex gear pump system there is no such problem, when not adjusted high when the main pump fluid directly through the left and right rocker hydraulic cylinder mesh group in the center (H), directly back to the tank. Control system with a single 4mLhr small hydraulic pump control, control oil circuit has a low pressure relief network (2MPa), to protect the control system and brake system oil pressure. When cranked up, the main pump fluid through the hydraulic cylinder, the remaining oil connected to the tank, full load, the pressure drop for the high-pressure relief section of the regulated pressure (20MPa). It can be seen that there is no power waste in this system.

From the above analysis, it can be seen that the application of duplex gear pump system in coal mining machine height adjustment system can significantly reduce the waste of power, reduce the oil temperature rise, shorten the length of the machine and increase the life of hydraulic components.

Key words: